Tài liệu miễn phí Tự động hoá
Download Tài liệu học tập miễn phí Tự động hoá
Variable voltage, variable frequency operation of induction machines is realised utilising autonomous
inverters, in conjunction with a rectifier and a DC link circuit. The voltage source inverter (VSI) is the
most frequently applied power supply source for speed control of induction motors. It can be operated in
six-step mode or in PWM mode. Six-step operation will be considered first.
8/29/2018 4:55:20 PM +00:00
As far as the AC machines are concerned, simple speed control systems are not capable of providing
decoupled (independent) flux and torque control. All the so called scalar speed control methods
(constant volts/hertz control, slip frequency control, voltage control etc.) are able of controlling the
steady-state behaviour of the machine only.
8/29/2018 4:55:20 PM +00:00
Decoupled flux and torque control of an induction machine can be realised by control of instantaneous
phase current values, which in turn can be achieved by stator current space vector magnitude and
position control with respect to the chosen flux space vector.
8/29/2018 4:55:20 PM +00:00
Equation of mechanical motion that describes rotor rotation is the same, irrespective of the type of the
electric machine under consideration. It is given with the well-known expression
8/29/2018 4:55:20 PM +00:00
Regarded as constant). Equations derived for the current-fed machine remain to be valid. Two coordinate
transformations are required: one transforms stator voltage d-q axis references into phase
voltage references,
8/29/2018 4:55:20 PM +00:00
Some characteristic simulation and experimental results are given in this Section, that illustrate
behaviour of rotor flux oriented induction machines. Current-fed indirect rotor flux oriented machine is
discussed at all times.
8/29/2018 4:55:20 PM +00:00
As both vector controlled induction machines and vector controlled SPMSM require current controlled
PWM inverter, then it is possible to discuss current control methods independently of the type of the
drive. In other words,
8/29/2018 4:55:20 PM +00:00
Summarising the procedure: speed loop is held open, d-axis current command is set to rated and q-axis
current command of the alternating square waveform is imposed.
8/29/2018 4:55:20 PM +00:00
It has been assumed so far in all the considerations of induction machine and SPMSM vector control
that a speed (or position) sensor is available and that it provides the required feedback signal for closed
loop speed control (and the speed/position information for co-ordinate transformation,
8/29/2018 4:55:20 PM +00:00
Tham khảo tài liệu 'học biến tần yaskawa f7', kỹ thuật - công nghệ, tự động hoá phục vụ nhu cầu học tập, nghiên cứu và làm việc hiệu quả
8/29/2018 4:55:20 PM +00:00
Hướng dẫn sử dụng biến tần G7
8/29/2018 4:55:20 PM +00:00
-Thiết kế và lắp đặt các hệ thống tự động, hệ thống hoạt động đồng bộ nhiều biến tần và các dự án về nguồn điện,...theo yêu cầu khách hàng.
-Bảo trì,sửa chữa các loại máy móc,thiết bị đo lường,biến tần,bộ nguồn,UPS của tất cả nhãn hiệu trên thế giới
-.Qui trình sửa chữa chuyên nghiệp, kỹ thuật viên nhiều kinh nghiệm được đào tạo bởi YASKAWA ENGINEERING & TDK-Lambda được sự giám sát của các chuyên gia Nhật Bản tại công ty cùng với sư hỗ trợ của các thiết bị o lường chính xác cao độ, máy móc sau khi...
8/29/2018 4:55:20 PM +00:00
Các model trng ho 3G3MV
8/29/2018 4:55:20 PM +00:00
Cấu trúc và lắp đặt
8/29/2018 4:55:20 PM +00:00
Chuẩn bị cho hoạt động và theo dõi
8/29/2018 4:55:20 PM +00:00
Chạy thử
8/29/2018 4:55:20 PM +00:00
Hoạt động cơ bản
8/29/2018 4:55:20 PM +00:00
Các chức năng hoạt động cao cấp
8/29/2018 4:55:20 PM +00:00
Các hoạt động bảo dưỡng
8/29/2018 4:55:20 PM +00:00
Dùng biến tần với motor
8/29/2018 4:55:20 PM +00:00
Tài liệu hướng dẫn sử dụng biến tần Siemens
8/29/2018 4:55:20 PM +00:00
Hướng dẫn sử dụng J7_Manual
8/29/2018 4:55:20 PM +00:00
Khái niệm chung , các công thức co bản
8/29/2018 4:55:20 PM +00:00
Micromaster Vector
8/29/2018 4:55:20 PM +00:00
Giới thiệu chung về biến áp
8/29/2018 4:55:20 PM +00:00
Một máy phát đồng bộ nối lưới có điện áp pha 6,3kV. Điện
kháng đồng bộ là 14Ω, bỏ qua điện trở stator.
8/29/2018 4:55:20 PM +00:00
Tổng quan máy điện đồng bộ
8/29/2018 4:55:20 PM +00:00
Một động cơ DC kích từ độc lập, 230V, điện trở phần ứng 0,2Ω, tốc
độ không tải lý tưởng là 1000 vòng/phút. Ở chế độ định mức dòng điện phần
ứng là 40A
8/29/2018 4:55:20 PM +00:00
Tổng quan máy điện một chiều
8/29/2018 4:55:20 PM +00:00
MICROMASTER 420 Inverter
8/29/2018 4:55:20 PM +00:00