Xem mẫu

BANCO PROVA Inverter 7,5Hp D truck USE AND MAINTENANCE INSTRUCTIONS Spin srl Via Casalecchio 35/G Rimini Italy 1 WARNING This symbol is used when the not compliance or the wrong application of the instructions for the use may cause damage to the people. ENVIRONMENTAL NOTICES NOISE PACKAGING OUT OF ORDER The machine has a high Lep value, more than 70 db(A ); therefore, make sure to wear ear protectors. If the machine is placed in an environment with a noise level higher than 80 db(A), the employer should inform and train the user about the dangers posed by the exposure to noise and take a decision in accordance with competent doctor’s instructions. Do not dispose of parts of the packaging in the dustbin, but divide them according to the material are made of (cartboard, wood, plastic, etc.) and dispose them in accordance with the local and national provisions in force. At the end of the Machine’s working life: 1 Disactivate the Machine, by disconnecting it from the electric power supply and cutting the supply line cable; 2 Disassemble the Electronic Panel and the related electronic board-card if present; 3 Disassemble the components, separating the various types. DISPOSAL At the end of the Machine’s working life, the parts, separated by the type of material, had to be disposed in conformity with the local and national laws in force. For the electric and electrenic devices, called Electrics and electronics Equipments (WEEE), according with EC Directives 2002/95/CE, 2002/96/CE and 2003/108/CE, the Manufacturer specifies: 3 NOT dispose of the equipment as municipal waste and separate collection is mandatory; 4 Ask the retailer about collection points authorised for regular disposal; 5 Stick to the standards for correct waste management, to prevent potential effects on the environment and human health; 6 The onside symbol indicates that separate collection of waste electrical and electronic equipment is mandatory for scrapping. 7 The distributor who does not comply with the mandatory separate waste collection of the professional WEEE is punished with a fine from € 30.000,00 to € 100.000,00. 2 1.0 General information 1.1 PURPOSE OF THE MANUAL This manual refers to the usage and maintenance of the test bench and it aims at providing a complete guide for the usage of the machine and its periodical maintenance. In order to use this bench properly, it is important to read carefully this manual. The machine is equipped with safety aiming at the prevention of damage to the operator. SPIN SRL declines any responsibility in case of improper use of the machine and of exclusion of safety devices by the operator. This manual is an integral part of the bench and it has always to be supplied together with it, also in case of sales. The machine is identified with a plate indicating the model, the year of manufacture and the serial number. The plate is placed at one side of the bench. Safety rules - The machine must be connected to a power plug which is protected against indirect. contacts in compliance with the provisions of the countries of use. - Disconnect the cord from the power supply before operating inside the bench. - Do not perform changes or manumissions to the micros of the safety system. - Do not use water in case of fire. - Use the machine in places protected against rain. - Do not keep at room temperature > 45°C. - Do not operate in an explosive atmosphere. Safety devices - Emergency stop - Carter pulley safety micro - Emergency Stop - Automatic switch (100A) on low voltage - If the safety micro is opened, the bench turns off and the engine does not start. There is voltage only on the low voltage part. Attention. In case of need press the emergency key “EMERGENCY STOP” 3 3.0 CONNECTIONS The machine must be plugged into a socket protected against the indirect contacts in compliance with the provisions in force in the country of use. Before switching on the machine, make sure that the network voltage is the one indicated in the apposite plate. After determining the power supply voltage, properly connect the bench to the power supply by using a cable through a protection switch. Connect the three cables to the batteries as indicated in figure 1 (the bridge for the series connection is not included). The batteries must be efficient, the bench is not provided with battery charger. Fig.1 Make sure that all the switches are turned off. After installing the voltage change bridge (according to your needs), install the general switch (52) and turn the trigger of the automatic switch (low pressure) on 1; the automatic switch is placed on the lower part of the bench; to reach it open the left door with the apposite supplied key. Then press the key “reset”; the display, the DC general switch (20) and the AC general switch (13) should turn on. 4 4.0 DESCRIPTION OF THE TEST BENCH SECTION TESTER (BLUE) Fig. 2 1 Diode test 2 Microfarad 3 Ohm 4 Ohm scale 10-100-1000-10000 selector 5 Diode plate test 6 Milliampere 7 Milliampere warning light 8 Diode test (+) warning light 9 Diode test (-) warning light 10 Ohm warning light 11 Microfarad warning light 12 Ohm-microfarad-milliampere selector 5 ... - tailieumienphi.vn
nguon tai.lieu . vn